..::AQUA CONTROL SUPPLY::..

Ruth/Berry Jet Pumps
1	N/A RB-325449 RB-325451 RB-325453	13-Gal. 14" x 20" Plastic Lined Tank 26-Gal. 16" x 31" Plastic Lined Tank 42-Tall 16" x 48" Plastic Lined Tank 42-Short 20" x 31" Plastic Lined Tank
2		Air Volume Control Type-L with tubing and fittings PUA-AVC-L
2		Pressure Gauge 2" x 100 lb. 1/4" MIP out bottom PGA-2X100
2A		Air Volume Control Tubing fits 1/4" Push-On Tubing fittings RB-AVCT
2A		Valve Stem fits US Gauge Brand Air Volume Controls fits 1/4" Push-On Tubing RB-302511
2A		Valve Stem fits old style Penn Brand Air Volume Controls bottom side is same thread a Snifter Air Valve RB-60053
3		Snifter Air Valve also known as a chrome air valve RB-101302
3A		Air Valve Adapter female air valve thread x 1/4" Push-On Tubing RB-302512
4		Large Brass Adapter Nut fits old style large brass adapter 2" FIP thread RB-325285
5		Rubber Seal for use with old style large brass adapter fits over 1" pipe RB-325202
5	Photo not available	Rubber Seal for use with old style large brass adapter fits over 1-1/4" pipe RB-325203
5A		S.S. Retainer ring for use with old style large brass adapter required when using 1" seal RB-325429
6		Large Brass Adapter 2" MIP tand side w/ O-Ring inside for 1-5/8 OD tubing 1-1/4" FIP inlet side thread on outlet RB-325290
7	GMPL-015	1-1/2" Galvanized Pipe Plug
7A	GMPL-002	1/4" Galvanized Plug
8	41-1223	O-Ring Rubber, 1-5/8" I.D. ( RB-325181 )
9		Shallow Well Jet Assembly black end is 1-3/8"OD and goes into Diverter other end is 1-5/8"OD and goes into brass tank adapter if to fit old style small brass adapter - you have to convert using a #4701-012 CPVC coupling and some 1-3/8" O.D. pipe RB-6235 1/2 H.P. 26 GAL RB-6237 1/2 H.P. 42 SHORT RB-6239 3/4 H.P. 26 GAL RB-6240 3/4 H.P. 42 SHORT
10	N/A	Grommet ( RB-325169 )
11	RB-325051	Motor Head Wire-26"
12	PUA-PPS-2040 PUA-PPS-3040 PUA-PPS-4060	Pressure Switch 1/4" FIP 20/40 Pressure Switch 1/4" FIP 30/40 Pressure Switch 1/4" FIP 40/60
13	RB-325510 RB-325512 RB-325516	-- Pump Assembly With Motor -- 1/2-HP FX,FXD 3/4-HP JX,JXD 1-HP KX,KXD Multi-Stage Nolonger Avalible
14	BOLT-HB-516010	5/16"-18T X 1" Cap Screw "Bolt" (10-needed)
15	BOLT-HN-0025	5/16"-18T Hex Nut (10-needed)
16	RB-325433	Cork Gasket
17	4700-012 4700-015	-- DW Suction Tube Single Stage -- 1-3/8" O.D. (For 1/3, 1/2, 3/4-HP Units) 1-5/8" O.D. (For 1,1-1/2, 2-HP Units)
18	4700-015	Upper Tube For 2-Stage Units 1-5/8" O.D.
19	4700-012	Lower Tube For 2-Stage Units 1-3/8" O.D.
20	4700-015	Upper Tube For 3-Stage Units 1-5/8" O.D.
21	4700-012	Lower Tube For 3-Stage Units 1-3/8" O.D.
22	GMHB-211	1-1/2" x 1" Galvinized Hex.Bushing
23		Small Brass Adapter Nut fits old style small brass adapter 1-1/4" FIP thread, fits over 1" pipe old Ruth/Berry number RB-325286 No Longer Available
24	RB-325288	Small Brass Adapter With 1-3/8" O-Ring - new style 1-1/2" mip tank side - new style 1-1/4" FIP pipe inlet - old style had 1-1/4" mip pipe inlet f/nut
25	SJW-012	Seal For 1" IPS Pipe - to fit old style brass adaper
26	R-225	1-3/8" I.D. O-Ring ( RB-325180 )
27	BOLT-HB-002020	1/4"-20T x 2"Long Bolt - 2 Needed F/ X,XD,FX,FXD,JX,JXD Units - 3 Needed F/ KX,KXD,LX,LXD,MX,MXD Units
28	BOLT-FW-002 BOLT-FW-0025	1/4" Flat Washer for Single-Stage Units 5/16" Flat Waher for Multi-Stage Units
29	BOLT-HN-002 BOLT-HN-0025	1/4"-20T Hex Nut for Single-Stage Units 5/16"-18T Hex Nut for Multi-Stage Units
30	BOLT-HB-516045	5/16"-18t x 4-1/2" Hex Bolt (4 Req'd)
31	RB-325223	5/16"-18t x 6-1/2" Hex Bolt (4 Req'd)
32		Shaft Seal 3/4" seal fits all single stage Ruth/Berry units RB-325494
32		Shaft Seal 3/4" seal fits all multi stage Ruth/Berry units RB-325495
33		Diverter for X, XD, FX and FXD units has 2 bolt holes fits 1-3/8" tubing -- with o-ring RB-325475 for JX and JXD units has 2 bolt holes fits 1-3/8" tubing -- with o-ring RB-325473 for KX,KXD,LX,LXD,MX,MXD has 3 bolt holes fits 1-5/8" tubing -- with o-ring RB-325471
34		Impeller with built in brass shaft for 1/2 HP -- X, XD, FX and FXD RB-325477 with built in brass shaft for 3/4 HP -- JX and JXD RB-325518 with built in brass shaft for 1 HP -- KX and KXD RB-325523 with built in brass shaft for 1-1/2 HP -- LX and LXD RB-325530 with built in brass shaft for 2 HP -- MX and MXD RB-325531
35		Cast-Iron Motor Bracket motor mounting flange has 4 bolt holes tank mounting flange has 10 bolt holes diverter mounting flange has 2 holes to fit X, XD, FX, FXD, JX and JXD units RB-325481
35		Cast-Iron Motor Bracket motor mounting flange has 4 bolt holes tank mounting flange has 10 bolt holes diverter mounting flange has 3 bolt holes to fit KX, KXD, LX, LXD, MX and MXD units RB-325482
35		Cast-Iron Motor Bracket motor mounting flange has 4 bolt holes tank mounting flange has 10 bolt holes diverter mounting flange has 4 holes to fit all 2 and 3 stage units RB-325483
36		Shaft Collar with set screws RB-325437
36		Set Screw Only 5/16" - 18T x 3/8" RB-325226
36		Set Screw Only 5/16" - 18T x 1/4" RB-325501
37	BOLT-HB-003007	Bolts for Motor 3/8"-16 x 3/4" (4 Req'd)
38	RB-325011 RB-325013 RB-325000	1/2-H.P. Motor Assembly 3/4-H.P. Motor Assembly 1-H.P. Motor Assembly
39		Front Diverter for all 2 and 3 stage units RB-325464
40		Brass Spacer Washer 1/32" Thick -- 5/8"ID x 7/8"OD RB-325440
41		Brass Spacer Washer 1/16" Thick -- 5/8"ID x 15/16"OD RB-325484
42		Back Diverter for all 2 and 3 stage units RB-325469
44	RB-325442	7/16"-20 SS Lock Nut
45	RB-325441	Brass Spacer Washer 1/8" Thick, 7/16"x7/8"
46		Front Impeller FP2D requires 1 RB-325504 JP2D and KP2D requires 1 LP3D requires 2 RB-325506 LP2D requires 1 MP3D requires 2 RB-325508
47		Back Impeller FP2D and JP2D RB-325505 KP2D and LP3D RB-325507 LP2D and MP3D RB-325509
48		Brass Shaft fits 2 stage units -- 3/4" x 5-1/8" long RB-325438 fits 3 stage units -- 3/4" x 6-7/8" long RB-325439
49	Photo not available	Center Diverter for 3 stage units RB-325468
.	RB-60078	Air Booster Kit
.	RB-325244	Hex Alen Wrench 1/8" T-Handle
.	RB-325245	Hex Alen Wrench 5/23" T-Handle